Suzuki EN125-2A Скачать руководство пользователя страница 157

Страница: 157 / 208

7-5

SERVICING INFORMATION

CHASSIS

Complaint

Battery runs down
quickly

Reversed battery polarity.

Battery "Sulfation"

Battery discharges too
rapidly

Symptom and possible causes

Remedy

1. The charging method is not correct.

2. Cell plates have lost much of their active

result of over-charging.

3. A short-circuit condition exists within the

due to excessive accumulation of

caused by the high electrolyte S.G.

4. Electrolyte S.G. is too low.

5. Contaminated electrolyte.

6. Battery is too old.

material

battery

sediments

Check the generator, regulator/rectifier and circuit

connections, and make necessary adjustments to

obtain specified charging operation.

Replace the battery, and correct the charging system.

Replace the battery.

Recharge the battery fully and adjust electrolyte S.G.

Replace the electrolyte, recharge thebattery and the

adjust S.G.

Replace the battery.

The battery has been connected the wrong way

round in the system, so that it is being charged in

the reverse direction.

1. Changing rate too low or too high.

(When not in use, batteries should be

least once a month to avoid

2. Battery electrolyte excessive or insuffi

specific gravity too high or

3. The battery left unused for too long in cold

climate.

recharged

sulfation.)

cient, or its

too low.

1. Dirty container tap and sides.

2. Impurities in the electrolyte or elec

too high.

trolyte S.G. is

Replace the battery and be sure to connect the

battery properly.

Replace the battery.

Keep the electrolyte up to the prescribed level, or

adjust the S.G. by consulting the battery maker's

directions.

Replace the battery, if badly sulfated.

Clean.

Change the electrolyte by consulting the battery

maker's directions.

Complaint

Steering feels too heavy
or stiff.

Steering oscillation.

Wobbly front wheel.

Front suspension too
stiff.

Front suspension too
soft.

Noisy front suspension.

Symptom and possible causes

Remedy

1. Steering stem nut vertightened.

2. Worn bearing or race in steering stem.

3. Distorted steering stem.

4. Not enough pressure in tires.

1. Loss of balance between right and left front suspensions.

2. Distorted front fork.

3. Distorted front axle or crooked tire.

Adjust.

Replace.

Adjust.

Replace.

Repair or replace.

Replace.

1.Distorted wheel rim.

2.Warn-down front wheel bearings.

3.Defective or incorrect tire.

4.Loose nut on axle.

1. Weakened springs.

2. Not enough fork oil.

1. For oil too viscous.

2. Too much fork oil.

1. Not enough fork oil.

2. Loose nuts on suspension.

Replace.

Retighten.

Replace.

Refill.

Replace.

Remove excess oil.

Refill.

Retighten.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды