Suzuki EN125-2A Скачать руководство пользователя страница 143

Страница: 143 / 208

CARBON BRUSHES

When the brushes are worn, the motor will be

unable to produce sufficient torque, and the

engine will be difficult to turn over. To prevent this,

periodically, inspect the length of the brushes,

replacing them when they are too short or chipping.

STARTER MOTOR INSPECTION

COMMUTATOR

If the commutator surface is dirty, starting per-

formance decreases. Polish the commutator with

#400 or similar fine emery paper when it is dirty.

After polishing it, wipe the commutator with a

clean dry cloth.

ARMATURE COIL

Using a pocket tester, check the coil for open and

ground by placing probe pins on each commutator

segment and rotor core (to test for ground) and on

any two segments at various places (to test for

open), with the brushes lifted off the commutator

surface.

If the coil is found to be open-circuited or ground-

ed, replace the armature. Continuous use of a

ctive armature will cause the starter motor to

suddenly fail.

efe

Pocket tester

09900-25002

ELECTRICAL SYSTEM 6-10

SEGMENT

MICA

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды