Suzuki EN125-2A Скачать руководство пользователя страница 55

Страница: 55 / 208

3-23

ENGINE

TOP RING AND 2ND RING

Install spacer

into the bottom ring groove first.

Then install both side rails

, one on each side of

the spacer. The spacer and side rails do not have a

specific top or bottom when they are new. When

reassembling used parts. Install them in their

original place and direction.

UPPER END COMPONENTS REASSEMBLY

OIL RING

Top ring and 2nd ring differ in the shape of ring

face and the face of top ring is chrome-plated

whereas that of 2nd ring is not. The color of 2nd

ring appears darker than that of the top one.

Top and 2nd rings have the letter R" marked on

the top. Be sure to bring the marked side to the top

when fitting them to the piston.

Position the gaps of the three rings as shown.

Before inserting piston into the cylinder, check

that the gaps are so located.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды