Suzuki EN125-2A Скачать руководство пользователя страница 28

Страница: 28 / 208

2-15

PERIODIC MAINTENANCE AND TUNE-UP PROCEDURES

TIRES

Inspect initial 1 000 km and Every 4 000 km

TIRE

Inspect the tires for wear and damage; and check

the tire tread depth as shown. Replace a badly

worn or damaged tire. A tire with its tread worn

down to the limit (in terms of tread depth) must be

replaced.

Check the tire pressure, and examine the valve for

evidence of air leakage.

TIRE TREAD DEPTH SERVICE LIMIT

Front

1.6 mm

Rear

1.6 mm

TIRE PRESSURE

Normal riding

kPa

kg/cm

Front

175

1.75

175

1.75

Rear

200

2.00

225

2.25

Cold inflation

tire pressure

Sold riding

Dual riding

Fist check if the brake system is properly

adjusted.

While operating the brake, check to see that the

extension line from the index mark is within the

range on the brake panel.

If the index mark is outside the range as shown

in the illustration at right, the brake shoe assy

should be replaced to ensure safe operation.

Brake lining wear limit

This motorcycle is equipped with brake lining wear

limit indicator on rear brake. As shown in the

illustration at right, at the condition of normal

lining wear, an extended line from the index mark

on the brake camshaft should be within the range

embossed on the brake panel with the brake on. To

check wear of the brake lining, follow the steps

below.

The extension line of the index mark is outside of the range.

The extension line of the index mark is within the range.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды