Suzuki EN125-2A Скачать руководство пользователя страница 89

Страница: 89 / 208

4-1

FUEL AND LUBRICATION SYSTEM

FUEL COCK

Turn fuel cock to "OFF" position and discon-

nect fuel line from the fue cock.

Place a clean oil pan under the fuel cock

assembly, turn fuel cock to "ON" position and

drain the fuel.

Unscrew the fuel cock securing bolts, and take

off the fuel cock assembly.

CLEANING

Rust from the fuel tank tends to build up in the

filter, which, when the filter has been neglected

for a long period, inhibits the flow of fuel.

Remove the rust from the filter using compressed

air.

DISASSEMBLY

WARNING:
Gasoline is very explosive. Extreme care
must be used.

WARNING:
Gasket must be replaced with a new one to
prevent leakage.

Gasket

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды