Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 60

Страница: 60 / 225

Design and function

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

5.9

Hydraulic system of machine

The hydraulic system of the machine:



can be operated at a maximum of 100 l/min.,



has been designed for open or closed-centre hydraulic systems. The conversion from open to

closed-centre hydraulic system is carried out by means of the load-sensing screw at the electro-

hydraulic control block.

All hydraulic functions of the machine are operated via the control set. The individual hydraulic

components of the machine are connected to the electro-hydraulic control block of the machine for this

purpose.

The hydraulic system of the machine is ready for operation if:



the electro-hydraulic control block has been connected to the hydraulic system of the tractor and



the oil circulation between tractor and machine has been switched on via the control device on

the tractor.



The actuating speed of the hydraulic functions (hydraulic

components) depends on the tractor's hydraulic system.

Depending on the tractor model, a correction of the set actuating

speed at the tractor's control device/the machine's control block

may be necessary.



For information about the required control devices, refer to the

chapter "Required tractor equipment", page 25. For information

about the hose markings, refer to the chapter "Marking of

hydraulic supply lines", page 17.

(1) Hose holder for proper deposition of supply

lines.

Fig. 31

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 60 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: