Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 38

Страница: 38 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

DANGER

DANGER
marks a direct danger bearing a high risk, which will cause most

serious bodily injury (loss of limbs or long-term harm) or even

death if it is not prevented.
Non-observance of the safety instructions marked by “DANGER“

directly causes most serious bodily injury or even death.

WARNING

WARNING
marks a possible danger bearing a moderate risk, which might

cause most serious bodily injury or even death if it is not

prevented.
Non-observance of the safety instructions marked by

“WARNING“ may cause most serious bodily injury or even

death.

CAUTION

CAUTION
marks a possible danger bearing a low risk, which might cause

light or moderate bodily injury or material damage if it is not

prevented.
Non-observance of the safety instructions marked by

"CAUTION" may cause light or moderate bodily injury or

material damage.

3.5.2

Important information

Important information:



provides details for proper use of the machine,



provides user hints for optimum use of the machine,



is marked by the following symbols.

IMPORTANT
marks an obligation to behave in a particular manner or to act in

a certain way, in order to use the machine properly.
Non-observance of these instructions may cause malfunctions

of the machine or in its vicinity.

INFORMATION
marks user hints and particularly useful information.
This information will help you to use all functions of your

machine in the best possible way.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 38 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: