Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 116

Страница: 116 / 225

Operation

116

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

(1) Screen. Depending on the selected

function, the following menu appears:



Working

menu. The

Working

displays the selected functions and the

operating states during charging and

discharging.



Road travel

menu. The

Road travel

menu appears with the road travel

mode activated.



SET

menu. The

SET

menu displays:



the software version,



machine parameters.

(2) Switch control system on (I)/off (0)
(3) Switch road travel mode on/off/ Scroll

through menu

(4) Switch crossover conveyor off
(5) Switch crossover conveyor on and change

driving direction

(6) Switch

Discharge mode A II

on/off

(7) Switch

Discharge mode A I

(8) Switch automatic charging system on/off
(9) Reverse transport floor/Reduce feed rate of

transport floor during discharge (in

combination with key 11)

(10) Double feed rate of transport floor for

complete emptying (transport floor level

II)/Increase feed rate of transport floor

during discharge (in combination with key

11)

Fig. 83

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 116 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: