manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 17 / 225

Поделиться
Скачать
Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 17

 

Product description

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

17 

 

 

 

  (1)  Bonnet 
  (2)  Hydraulics protective device 
  (3)  Holding-down device with pulley 
  (4)  Drawbar protective device 
  (5)  Protective casing, pick-up 
  (6)  Hinge carrier, left-hand 
  (7)  Side protector, left-hand 
  (8)  Access door to cargo space 
  (9)  Side protector, beater drive, left-hand 

   (10)  Sensor protective device 

 (11)  Tailgate 
 (12)  Bottom plates for feed shaft   
 (13)  Stripper plate 
 (14)  Side protector, beater drive, right-hand 
 (15)  Tunnel cover for beater drive 
 (16)  Side protector, right-hand 
 (17)  Guide wheels 
 (18)  Hinge carrier, right-hand 

 

 

 

 

  

2.3 

Supply lines between tractor and machine 

 

 

  (1)  Hydraulic connector "Flow line" SN 16 (red) 
  (2)  Hydraulic connector "Return line" SN 20 

(blue) 

  (3)  Load-sensing connector SN 6 (only with 

available load-sensing connector) 

  (4)  Compressed-air brake, feed line (red) 
  (5)  Compressed-air brake, brake line (yellow) 
  (6)  Lighting connector, 7-pole 
  (7)  Power supply, 3-pole 
  (8)  ISOBUS connector for ISOBUS control unit 

(only with available ISOBUS control unit) 

  (9)  Hydraulic connector for hydraulic brake 

system with hydraulic clutch according to 

ISO 5676 (only with available hydraulic 

brake system) 

 

 

 

Fig. 3 

 

 

  

2.3.1 

Marking of hydraulic supply lines 

  

Hydraulic connector "Flow line" 

 

Label 

 

  Arrows: white 

 

  Background: red 

 

 

 
Hydraulic connector "Return line" 

 

Label 

 

  Arrows: white 

 

  Background: blue 

 

 

 

 

 

Содержание Super-Vitesse CFS 3101


































































































































































































































Отзывы:

Нет отзывов