Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 97

Страница: 97 / 225

Commissioning

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

6.6

Mount shell to folding drawbar

Shop work

Only an authorised workshop is allowed to mount the shell to the

folding drawbar.

Assembly instructions for authorized workshop:

1. Mount the washer (1).
2. Fasten the shell (2) by means of the two

screws (3).

3. Tighten the nuts of the screws (3) at a

tightening torque of 2300 Nm.

Fig. 69

6.7

Mount crossover conveyor

Two people are required for mounting the crossover conveyor.

1. Hitch the machine to the tractor.
2. Check whether the tailgate is completely

closed. If not, close the tailgate completely.

3. Completely lower the folding drawbar.
4. Secure tractor and machine against

accidental starting and rolling.

5. Adjust the lamp brackets (1) with respect to

the tailgate (2):
5.1 Lift the lamp brackets (1).
5.2 Pull the locking bolt (3) out as far as it

will go.

5.3 Tilt the lamp bracket (1) over to the

rear.

5.4 Position the lamp bracket (1) in the

rear keyhole profile (4) by means of

the locking bolt (3).

5.5 Press the lamp bracket (1) down

again.

6. Unlock the tailgate from its closed position:

6.1 Always use one hand to hold the

Fig. 70

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 97 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: