Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 150

Страница: 150 / 225

Use of machine

150

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

WARNING

Risk of crushing, shearing, being drawn in and becoming

entangled to people within the hazardous area of the powered

transport floor, especially at the deflection points!



Keep sufficient safe distance to the powered transport floor.



Make sure that people leave the hazardous area of the transport

floor before switching on the transport floor feed.



Always keep the transport floor chain tightened.



Switch the transport floor feed off as soon as it is no longer

required.

WARNING

Risk due to failure of components in case of actuation of the

overload clutch!

Immediately switch the tractor's p.t.o. shaft off in case of actuation of

the overload clutch.

Check the machine for visible defects every day.
Immediately remedy or have remedied visible defects.

Clean the cutting unit, in particular the retainer of the cutting knives,

and the cutting knives themselves every day.

Permanent oil circulation between tractor and machine is required for

initiating the individual hydraulic functions.

10.1

Charging

WARNING

Risk due to incorrect use of the tractor if this causes failure of

components, insufficient stability and insufficient steerability

and braking ability of the tractor!

Observe the maximum loading capacity of the attached/hitched

machine and the admissible axle and tongue loads of the tractor. Run

the machine being only partly filled if necessary.

WARNING

Risk of crushing, shearing and risk of impact when lowering and

lifting the pick-up!

Make sure that people leave the hazardous area of the pick-up before

lowering or lifting the pick-up.

WARNING

Risk of becoming entangled, wound up and being drawn in

within the area of the movable pick-up components!

Make sure that people leave the pick-up area before switching the

pick-up drive on.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 150 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: