Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 184

Страница: 184 / 225

Service and maintenance of machine

184

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

12.10.2.2 Install cutting knives

WARNING

Risk of crushing and shearing when extending the cutting unit

into the conveyor duct!

Extending the cutting unit into the conveyor duct is not allowed if:



people are beneath the machine,



people may reach or reach into the dangerous spots alongside

the cutting unit.

1. Wear protective goggles.
2. Use compressed air to clean the slots for

the cutting knives.

3. Put the cutting knife (1) onto the knife lever

(2).

4. Pull the locking lever (3) up and insert the

cutting knife from the top into the knife

holder (4).

When installing the cutting knives,

ensure that the locking lever

completely engages again. The

locking lever has completely engaged

if it is in close contact with the frame

(5) of the cutting unit, the slotted

dowel pin (6) being at the front in the

oblong hole.

5. Refix the mounting lever and the knife lever

in the holder.

6. Fold the cover plate (7) up again.
7. Lock the cover plate by means of the bolt

(8) in the oblong hole (9).

8. Release the parking brake of the machine

after all cutting knives have been

reinstalled.

9. Start the tractor engine.
10. Switch the oil circulation between tractor

and machine on with the tractor engine

running.

11. Lower the pick-up.
12. Switch the tractor's p.t.o. shaft on.

Pick-up and feeder rotor are powered.

Fig. 115

Fig. 116

13. Extend the cutting unit into the conveyor

duct via the control set.

14. Lower the folding drawbar.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 184 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: