Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 140

Страница: 140 / 225

Operation

140

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

3. Press the

key once.



The

Working

menu appears.

7.3

SES system

Optional extra

7.3.1

Design

Fig. 86

The SES system (SES = Strautmann Electronic Steering) mainly consists of:



the control set (1),



the steering computer (2),



the angle sensors (3) at the drawbar and the axle to determine the required steering angle,



the speed sensors (4),



the hydraulic components (5),



the pressure switch (6).

Via 2 angle sensors and 2 speed sensors, the SES system electronically registers the required

steering angle which is adjusted to the speed, and transforms the required steering angle into an

electrical signal. The steering computer transmits the information to an electrically actuated hydraulic

valve and thus controls the steering cylinders of the steerable axles. The pressure switch registers the

pressure in the hydraulic system. If the hydraulic pressure is below 25 bar, the SES system is not

ready for operation. The pressure switch reacts as soon as the hydraulic pressure falls below 25 bar

and activates the follow-up steering system.
The SES system:



controls depending on the speed,



informs about malfunctions of the steering system via acoustic and visual warning messages on

the control set,

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 140 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: