Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 190

Страница: 190 / 225

Service and maintenance of machine

190

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

12.11.2 Lubricate chain tensioners and deflection points of transport floor

Lubricate chain tensioners and front deflection points of transport floor chain

1. Lift the folding drawbar to increase the free

space to the chain tensioners.

2. Secure tractor and machine against

accidental starting and rolling.

3. Lubricate the chain tensioners.
4. Lubricate the front deflection points of the

transport floor chain.

Lubricate rear deflection points of transport floor chain

1. Open the tailgate.
2. Secure tractor and machine against

accidental starting and rolling.

3. Swivel the stop-cock to position "0" (stop-

cock closed).



Tailgate is secured against accidental

lowering.

4. Lubricate the rear deflection points of the

transport floor chain.

12.12 Dosing drums

WARNING

Risk of slipping, stumbling or falling when carrying out service

and maintenance work on the roller chains for the dosing drum

drive!

Absolutely use a mobile service platform with ladder when carrying

out service and maintenance work on the roller chains for the dosing

drum drive.

12.12.1 Lubricate roller chains of dosing drums

1. Use a service platform with ladder:



to open the protective devices for the roller chains by means of a tool,



to obtain safe access to the roller chains.

2. Lubricate the roller chains by means of grease or engine oil.
3. Close the protective devices and lock them in protective position.

12.12.2 Check/Retighten tension of roller chains of dosing drums

The roller chains must be retightened if they can be pushed in by

more than 5 mm.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 190 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: