Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 199

Страница: 199 / 225

Service and maintenance of machine

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

199

12.16 Maintenance of axles

Fig.

135

Fig.

136

Lubrication and maintenance plan

Axles

Befo

re s

tart

-up

d af

ter

lon

r d

ownt

ime

Afte

r f

irs

t j

ourney

ith

loa

teria

ery

erv

urs

ery

0 s

erv

e ho

urs

ery

0 s

erv

e ho

urs

ce a

ear

ery

00 s

erv

e h

ce a

ear

Lubricate

with long-life grease

(1) Lubricate knuckle arm bearing.

(2) Lubricate locking cylinder heads of follow-up steering axle.

(3) Lubricate brake shaft bearing.

(4) Lubricate standard slack adjuster.

(5) Lubricate automatic slack adjuster.

(6) Have grease of wheel hub bearing changed (shop work!).

Maintenance work

[1] Check wheel nuts for tightness, retighten if necessary.

X** X

[2] Check clearance of wheel hub bearing, have it readjusted if

necessary (shop work!).

[3] Check brake linings for damage and wear, have them

replaced if necessary (shop work!).

[4] Check brake setting at brake lever, have it adjusted if

necessary (shop work!).

[5] Check brake setting at standard slack adjuster, have it

adjusted if necessary (shop work!).

[8] Check brake setting at automatic slack adjuster, have it

adjusted if necessary (shop work!).

[9] Check automatic slack adjuster for proper functioning.

* Also after each change of brake linings.
** Also after each wheel change.

Relubricate all lubrication points after cleaning the machine by means

of pressure washers.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 199 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: