Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 176

Страница: 176 / 225

Service and maintenance of machine

176

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

1. Unscrew and remove the two screws of the

protective casing of the pick-up (1).

2. Remove the protective casing of the pick-

up.

3. Unlock and unscrew the groove nut (2).

Remember exactly the number of

turns made to unscrew the groove

nut to ensure that the friction clutch

can be properly pre-tightened again!

4. Fix the protective casing of the pick-up to

the machine by means of the two screws.

5. Start the tractor engine.
6. Charge the machine with material to be

loaded for a short time such that the stuck

friction clutch slips for 2 to 3 seconds and is

freed (excessive slipping will damage the

friction linings).

Repeat this procedure up to three times if

the friction clutch does not slip.

  7.  Turn the tractor engine off.
  8.  Pull the ignition key out.
  9.  Unscrew and remove the two screws of the

protective casing of the pick-up.

10. Remove the protective casing of the pick-

up.

11. Retighten the groove nut with the exact

number of turns made for unscrewing.

Torque of friction clutch: 900-1000 Nm

12. Lock the groove nut.
13. Fix the protective casing of the pick-up to

the machine by means of the two screws.

Fig. 101

Fig. 102

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 176 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: