Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 134

Страница: 134 / 225

Operation

134

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

7.2.4.1 Call up SET menu

1. Press and hold the

key once.



After switching to the

SET

menu, the arrow

(1) is at the top and is pointing to the right.

Now the right-hand functions 2 to 4 can be

selected.

2. Briefly press the

key to move the

arrow down.

3. Press and hold the

key such that the

arrow is pointing to the left.



Now the left-hand functions 6 to 7 can be

selected.

4. Use the

and

keys to change

the values by 0.1.

5. Press the

key once.



The

Working

menu appears.

The screen shows:

(1) Arrow

(2) Only for machines equipped with dosing

drums: Entry of time during which the

transport floor shall reverse if the "Forage

wagon full" switch is switched on when

starting

Discharge mode A II

(3) Only for machines equipped with dosing

drums: Entry of time during which the

tailgate shall be activated after reaching the

"First opening width" sensor.

(4) Crossover conveyor display:



an arrow indicates the direction in

which the crossover conveyor starts to

run



"X" indicates that a crossover conveyor

is not available



"W" indicates that the Wollschläger

hydraulic system is used

(5) Display of potentiometer position:



value from 0 to 100



"KAL" appears during the calibration

procedure

(6) Left: Display of current software version

Right: Entry whether equipped with dosing

drums or not; here "with dosing drums"

  (7)  Entry of steering axle model
  (8)  Vacant
  (9)  Display of total number of service hours

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 134 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: