Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 141

Страница: 141 / 225

Operation

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

141



is equipped with a safety circuit such that in case of malfunctions the steering system works as a

pure follow-up steering system,



allows error diagnosis.

7.3.2

Steering computer displays

The steering computer (1) is equipped with an

additional module (2). As soon as the steering

computer is connected to the power supply, the

display of the additional module shows a status

message.
Open the cover (3) to read the status message.
1. Turn the Camlock lock.
2. Slightly lift the cover and then fold it down.

Fig. 87

(1) Display: Depending on the status, the

following appears:



a status indication or



an error message.

(2) ESC; exit menu/ one input position back
(3) MINUS; reduce value/ one selection item

back

(4) PLUS; increase value/ one selection item

forward

(5) ENTER; confirm value/ store value/ activate

selected menu/ one input position forward

Fig. 88

The following read-outs are available:

Read-out

Explanation

READY

The hydraulic system is ready for operation

Standby

The hydraulic system is not ready for operation, the hydraulic supply is not

available

COUPLING

The steering rods are not coupled or the specified steering range has been

exceeded

alarm code
xxx-xxx-xx

Error message; an active error has been detected

If several active errors are detected, the respective error messages will be displayed one after the

other.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 141 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: