Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 41

Страница: 41 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

87007122
Risk of electrical shock or burns due to accidental touching of electrical

overhead lines or due to inadmissible approach to high-voltage overhead

lines!

This risk may cause most serious injuries or even death.
Keep sufficient safe distance to high-voltage overhead lines.

Nominal voltage

Safe distance to overhead lines

up to 1 kV

1 m

over 1 up to 110 kV

3 m

over 110 up to 220 kV

4 m

over 220 up to 380 kV

5 m

nominal voltage unknown

5 m

87007123
Risk due to hydraulic oil squirting out under high pressure, caused by

leaking hydraulic hose pipes!

This risk may cause most serious injuries or even death if hydraulic oil squirting out

under high pressure enters the skin and the body.



Never try to block hydraulic hose pipe leaks with your hands or fingers.



Read and observe the information included in the operating instructions

before carrying out service and maintenance work on hydraulic hose pipes.

87007124
Risk due to explosion or hydraulic oil squirting out under high pressure,

caused by the pressure accumulator being under gas and oil pressure!

This risk may cause most serious injuries or even death if hydraulic oil squirting out

under high pressure enters the skin and the body.



Read and observe the information included in the operating instructions

before carrying out any work on the hydraulic system.



If injuries caused by hydraulic oil occur, immediately contact the medical

services.

87007126
Risk to any part of the body of being rolled over by the machine due to

accidental rolling of the machine parked in unsecured condition!

This risk may cause most serious injuries or even death.
Secure the machine against accidental rolling before unhitching the machine from

the tractor or before parking the machine. Use the parking brake and/or the

chock(s) for this purpose.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 41 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: