Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 130

Страница: 130 / 225

Operation

130

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

1. Press the

key once.



The steering axle is locked in "Straight"

position. The "Steering axle locked" symbol

appears and a beep is emitted.



If the symbol is flashing, the steering axle

could not be completely locked. Check the

steering system.

The screen shows:

Unlock steering axle

1. Press the

key once.



The steering axle can move freely (is

unlocked) and follows the turning radius of

the corner during cornering. The "Steering

axle unlocked" symbol appears and a beep

is emitted.

The screen shows:

Lock steering axle in SES system

WARNING

Risk to people due to insufficient stability and tipping over of the

machine if the steering axle is not properly used!

Absolutely lock the steering axle before travelling over the bunker silo

by means of the

Discharge mode A I

key.

Align the wheels of the steering axle in a straight line by means of a

short forward travel of the tractor and the hitched machine before

locking the steering axle.

Discharge mode A I

, the steering axle is automatically locked at

speeds up to 12 km/h.

In the case of the electro-hydraulic forced steering axle system, the

key has a touch-control design.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 130 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: