manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 162 / 225

Поделиться
Скачать
Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 162

Transport journeys

 

 

 

162 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

 

 

 

11 

Transport journeys 

 

 

A transport journey is a journey of the charged or empty machine to or from the place of operation. 

 

 

 

Observe the information in the chapter "Basic safety instructions", 

page 30. 

 

 

 

WARNING 

 

Risk due to incorrect use of the tractor if this causes failure of 

components, insufficient stability and insufficient steerability 

and braking ability of the tractor! 

Observe the maximum loading capacity of the attached/hitched 

machine and the admissible axle and tongue loads of the tractor. Run 

the machine being only partly filled if necessary. 

 

  

WARNING 

 

Risk to people due to accidental actuation of hydraulic functions 

during transport journeys! 

Switch the 

Road travel mode

 on before carrying out transport 

journeys. 

 

 

 

WARNING 

 

Risk to people due to insufficient stability and tipping over of the 

machine if the steering axle is not properly used! 

It is absolutely necessary to lock the steering axle: 

 

before travelling over bunker silos, 

 

at travelling speeds of more than 40 km/h, 

 

on rough road tracks, 

 

when traversing hills, 

 

before carrying out reverse travels. 

 

  

 

Observe the fact that the driving characteristics of the tractor are 

influenced by the load, in particular if the machine is partly empty. 

 

 

 

 

If the folding drawbar is equipped with a drawbar suspension, the 

hydraulic cylinders of the folding drawbar must be extended by 

approx. 20 mm before switching the road travel mode on. 
The drawbar suspension will not work if the folding drawbar is 

lowered to its end position. 

 

 

 

  1.  Lower the lift axle completely if available. 
 

  Only with the lift axle completely lowered is the ALB regulator able to properly control the 

required braking force. 

  2.  Deactivate the automatic charging system and close the front panel. 
  3.  Activate the 

Road Travel mode

 on your control set. 

    With the 

Road Travel mode

 switched on: 

 

the 

Road Travel 

menu appears, 

 

apart from the functions "Lock steering axle" and "Unlock steering axle", all other functions 

on the control set are disabled, 

Содержание Super-Vitesse CFS 3101


































































































































































































































Отзывы:

Нет отзывов