Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 25

Страница: 25 / 225

Product description

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

2.10

Required tractor equipment

The employed tractor must meet the following requirements, in order to ensure correct use of the

machine:

Tractor engine output and p.t.o. speed

Super-Vitesse CFS

3101

3101 DO

3501

3501 DO

Power required

120

130

P.t.o. speed

min

-1

1000

Electrical system

Battery voltage:



12 V (volt)

Socket for lighting:



7-pole

Socket for control set:



3-pole (DIN 9680). The feed line of the 3-pole socket should

have a minimum cable cross section of 4 mm².

Hydraulics



Check the compatibility of the hydraulic oils before connecting

the machine to the hydraulic system of your tractor. For details

about checking the compatibility of the hydraulic oils, contact

your agricultural machinery dealer if necessary.



Do not mix mineral oils with bio oils.

Maximum operating pressure: 200 bar
Delivery rate: min. 40 l/min at 180 bar, max. 100 l/min at 200 bar
Hydraulic oil of machine: HLP 46

Depending on their function, the hydraulic components can be

connected to:



a double-acting control device,



a single-acting control device and a depressurised return line

leading directly into the hydraulic oil tank of the tractor.

Given a free choice, we recommend a single-acting control device

and a depressurised return line. The hydraulic oil flows back into the

hydraulic oil tank of the tractor through the free return line with a low

back pressure. Thus, a free return line reduces heating-up of the

hydraulic oil.

The hydraulic hose pipes are marked by colours at the hydraulic

plugs, see chapter „Marking of hydraulic supply lines“, page 17.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 25 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: