manualshive.com logo in svg

SRS Labs QMS 100 Series, Руководство пользователя

Поделиться
Скачать
SRS Labs QMS 100 Series Скачать руководство пользователя страница 49

 

 

General Utilities    2-19 

 

 

SRS QMS Gas Analyzer 

3.

 

Use the Next Item or Previous Item from the View menu to view the 
sequential logs (The time and date of the scan appears on each log). 

Browsing Through the Gas Library 

Library Browsing Description 
There are several ways to browse through the gas library depending on the display mode and 
whether the Library Search utility is active. The Library display mode and search utility are 
linked together to provide an intuitive interface to locate and view any gas in the library file. 
 
Library Display mode only: 

1.

 

Activate the Library mode by selecting the Library command from the Mode 
menu. 

2.

 

Use the Next Item and Previous Item in the View menu to plot the next and 
previous gases in the list (you may also use the left and right arrow keys). 

Library Search utility only:  

You may start this utility from any display mode 

1.

 

Start the search utility by selecting the Library Search command from the 
Utilities menu. 

2.

 

Press the Show All button to list all available gases. 

3.

 

Use the scroll bar, and/or the keyboard to search the list or use the Search 
Masses section to look for specific gases. 

Library Display mode AND Search Utility: 
The combination of these two modes provides a very quick way to look for gases. 

1.

 

Make sure both the Library mode and the Library Search utility are active (see 
procedure above). 

2.

 

If you want to plot a gas, double click on its name in the Search utility dialog 
box or click on it once (to highlight it) and press the plot button. The gas 
fragment pattern will then appear as a histogram in the Library display. 

Analyzing the Mass Spectrum 

Spectrum Analysis description 

This utility provides the user with immediate analysis of residual gas based on a complete 
histogram or analog scan. Using a matrix inversion technique, the composition of the residual 
gas is analyzed and the best approximation to its composition is given in either pressure units or 
percentages. The user can enable up to 12 common gases for analysis. 
 
Note: Analysis mode is only available in Analog mode or Histogram mode. The mass range must 
be at least from 1 to 50 amu. 

Содержание QMS 100 Series

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды