SRS Labs QMS 100 Series Скачать руководство пользователя страница 174

Страница: 174 / 280

3-50 RGA Command Set

SRS QMS Gas Analyzer

different from that of the Bayard Alpert gauge readings.

Expect to see deviations between the two

gauges as the composition of a residual gas changes.

Parameters

TP0:

TP_Flag is cleared. Total Pressure measurement is disallowed and a null current value is returned

as a response to a total Pressure Measurement request (note that this includes the total pressure
measurement requests at the end of scans!).

TP1:

TP_Flag is set. Total pressure measurement is fully enabled.

TP?:

Total Pressure query. A total pressure measurement is triggered and a total ion current value is

returned over RS232. The actual response to the command depends on the status of TP_Flag as described
above.

Error Checking:

The absence of a parameter is considered an error.

Содержание QMS 100 Series

























































































































































































































































































Результаты поиска

Содержание QMS 100 Series

Отзывы:

Бренды по названию

Популярные бренды

SRS Labs QMS 100 Series, Руководство пользователя

Результаты поиска

Содержание QMS 100 Series

Отзывы:

Бренды по названию

Популярные бренды