Sony PCM-D10 Скачать руководство пользователя страница 65

Страница: 65 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

4-8. XLR ASSY, SW BOARD SECTION

352

351

359

360

353

355

357

356

358

WR1

WR2

SP1
(See Note)

FFC1

351

351
351

351

352

355

362

361

front cabinet section

front side

rear side

top side

bottom side

354

(See Note)

351

474733001

SCREW, +-Z 1.7X4.5

352

334899881

SCREW (M1.4) (L = 2.5 mm)

353

474249101

PLATE (PWB), MS

354

A5000096A

SW BOARD, COMPLETE (See Note)

355

474101501

KNOB (HOLD) (MIC ATT switch, HOLD switch)

356

474103001

CHASSIS (SD CARD)

357

A2226559A

SW_R BOARD, COMPLETE

358

474101201 BUTTON

(LIGHT)

359

474101401 KNOB

(POWER)

360

474101301

BUTTON (VOL) (+, -)

361

500166801

SPACER (XLR FRONT)

(width 7.5 X thickness 1.65 mm)

362

500166901 SPACER (XLR REAR) (width 6.0 X thickness 2.15 mm)

FFC1

191280111

CABLE, FLEXIBLE FLAT (18P)

SP1

X50000091

SVX XLR ASSY (Including XLR board,

Loudspeaker (1.6 cm), Holder (strap), Chassis (XLR),
Plate, Cushion (SP), Mesh (SP), Adhesive sheet (SP),

Sheet (SP), Screw) (See Note)

WR1 191281111

SHIELD WIRE L (WHT/BLK)

WR2

191281211

SHIELD WIRE R (RED/BLK)

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

Note:

When the complete SW board (Ref. No. 354) or SLV XLR assy
(Ref. No. SP1) are replaced, make sure to refer to “XLR/TRS JACK
CHECKING METHOD” on page 15, and check the XLR/TRS jack.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 65 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: