Sony PCM-D10 Скачать руководство пользователя страница 40

Страница: 40 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-19. NFC ANTENNA

Insert straight into the interior.

Insert at a slant.

FPC

connector

FPC

connector

How to install the FPC

  Insert the FPC straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

front side

top side

bottom side

terminal side

top side

NFC antenna FPC

connector
(CN361)

Unlock the connector.

adhesive tape
(sub material)

Peel the NFC antenna FPC

off of the adhesive tape.

– Bottom view –

Draw the NFC antenna FPC

out of the connector.

NFC antenna

NFC antenna FPC

3DVWLQJSRVLWLRQRIWKH1)&DQWHQQD)3&

guide line
(chassis (rear))

guide line

Protrusions of the FPC contact
the edge of the chassis (rear).

The FPC is affixed at a slant.
(Does not follow the guide line)

Protrusions of the FPC
do not contact the edge
of the chassis (rear).

protrusion

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 40 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: