Sony PCM-D10 Скачать руководство пользователя страница 26

Страница: 26 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-4. ORNAMENT (REC VOL), KNOB REC VOL ASSY, L KNOB (REC VOL)

top side

Pull out the knob REC VOL

assy in the direction of the

arrow.

R knob (REC VOL)

hole

Insert a flat blade screwdriver into

the holes, and use it to push out

the claws of the ornament (REC VOL)

to remove the ornament.

Insert a flat blade screwdriver into

the holes, and use it to push out

the claws of the ornament (REC VOL)

to remove the ornament.

hole (position of
scale mark “6”)

hole (position of
scale mark “0”)

ornament

(REC

VOL)

two

claws

screw (M1.4)

(L = 2.5 mm)

knob REC VOL assy

L knob

(REC

VOL)

block

L knob

(REC

VOL)

claw (narrow)

(total six claws)

hole (total six holes)

inside
(unit side)

outside
(knob REC VOL
assy side)

rubber (REC VOL)

Note

When installing the rubber

(REC VOL), align the six

holes and six claws (narrow).

• Installation direction for the rubber (REC VOL)

– Inside –

– Outside –

claw (narrow)
(total six claws)

claw (wide)
(total six claws)

• How to install the knob REC VOL assy

hole

shaft

knob REC VOL assy

When installing the knob REC VOL assy,
align the hole and shaft of the D cut shape.

Note 1:

When the knob REC VOL assy and L knob (REC VOL) are installed,

refer to “2-5 CHECKING OPERATION OF THE KNOB (REC VOL)”

on page 27.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 26 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: