Sony PCM-D10 Скачать руководство пользователя страница 35

Страница: 35 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-13. CHASSIS BLOCK/FRONT BLOCK-1

• Continued on 2-14 (page 36).

Soldering the shield

wire L [white].

Attach in order from

• Shield wire setting

front side

top side

bottom side

top side

top
side

Remove two solder

of the shield wire L.

[white/black]

Remove two solder

of the shield wire R.

[red/black]

MAIN board

groove

Soldering the shield

wire L [black].

Soldering the shield

wire R [black].

Soldering the shield

wire R [red].

Press the shield wire L

into the groove.

Press the shield wire R

into the groove.

NFC antenna
(See Fig. E)

adhesive sheet (XLR)

(See Fig. D)

top side

NFC antenna

guide line

• Pasting position of the NFC antenna

guide line

NFC antenna

adhesive
sheet
(XLR)

< Fig. D >

< Fig. E >

• Pasting position of the adhesive sheet (XLR)

Note 1:

Use the soldering iron vertically so that it

does not touch the cabinet portion.

cabinet portion

MAIN board

adhesive sheet (XLR)

(See Fig. D)

spacer (NFC)
(See Fig. E)

XLR assy

bottom side

alignment mark

guide line

XLR assy

spacer (NFC)

Peel the NFC antenna and spacer (NFC)

off of the XLR assy.

Note

The spacer (NFC) is affixed between

the NFC antenna and XLR assy.

When peeling off the NFC antenna

from the XLR assy, the spacer (NFC)

may also be peeled off.

The spacer (NFC) is included in the

repair parts for the NFC antenna.

When affixing the spacer (NFC) and NFC antenna to the XLR assy,
check the alignment marks on the XLR assy and follow the guide lines.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 35 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: