Sony PCM-D10 Скачать руководство пользователя страница 28

Страница: 28 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-6. REAR CABINET BLOCK

Open the lid (battery).

four screws

(Z1.7

4.5)

two screws (M1.4)

(L = 3.0 mm)

JIG

When disassembling the unit, use the following jig.

Part No.

Description

9-913-402-33 TOOL FOR DISASSEMBLING

front side

top side

bottom side

Close the lid (battery).

two slits

rear cabinet

front cabinet

Insert a flat-head screwdriver into

the two slits on the top of the unit,

and open a gap between the rear

cabinet and front cabinet.

Insert the jig into the space

and slowly remove the rear

cabinet

block.

Note:

When using a jig, please

work carefully so as not

to damage the rear cabinet

and front cabinet.

While moving the jig in

the direction of the arrow,

remove all claws and

the rear cabinet block.

three claws

Peel the rear cabinet block off

of the adhesive sheet (XLR).

three claws

five claws

claw

rear cabinet block

top side

guide line

NFC antenna

adhesive
sheet
(XLR)

3DVWLQJSRVLWLRQRIWKHDGKHVLYHVKHHW;/5

While moving the jig in

the direction of the arrow,

remove all claws and

the rear cabinet block.

Insert the jig into the space

and slowly remove the rear

cabinet

block.

Note:

When using a jig, please

work carefully so as not

to damage the rear cabinet

and front cabinet.

5HIHUHQFHILJXUH

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 28 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: