
PCM-D10
55
Sony CONFIDENTIAL
For Authorized Servicer
4-12. Factory
Shipment
It can be initialize to the factory shipment state and release the test
mode.
Note 1:
After the repair of this unit has been completed all, before
returning this unit to customer, be sure to execute.
Executing “Factory Shipment” will initialize the built-in
memory
fi
les and settings. Backup the built-in memory
fi
les to a PC or SD card beforehand, and after executing
“Factory Shipment”, transfer the
fi
les to the same folder in
the device again.
Procedure:
1. Enter the test mode.
(Refer to “1. SETTING THE TEST MODE” on page 51)
2. Press the [
v
DPC]/[ A-B
V
] buttons to select the “Factory
Shipment”.
Sleep
OFF DeepSleep
Power Down
Key Count
HotPlug Count
Log
Erase IPL2
Initialize Menu
Factory Shipment
Test mode menu screen
3. Press the [
N
] button to display the initialized screen.
EXEC : Play
Screen display
4. The [
N
] button is pressed,
fi
les and settings of the built-in
memory is initialized. Then test mode is released and reboot.
Note 2:
“BD address”, “iSerial” and “LCD contrast” are not initialized.
Files, menu settings and clock display of the built-in memory is all
initialized.
5. The
fi
le of built-in memory that was backup beforehand, return
to the same folder of this unit.
4-13. Key
Check
Operation of buttons and switches can be checked.
Procedure:
1. Enter the test mode.
(Refer to “1. SETTING THE TEST MODE” on page 51)
2. Press
the
[
v
DPC]/[ A-B
V
] buttons to select the “Key Check”.
OFF DeepSleep
Power Down
Key Count
HotPlug Count
Log
Erase IPL2
Initialize Menu
Factory Shipment
Key Check
Test mode menu screen
3. Press the [
N
] button to display the button/switch operation
check screen.
(Displayed characters/values in the following
fi
gure are exam-
ple)
Trackmark
REMAIN : 31
Screen display
Confirmed button/switch name
(It is blank immediately after
entering the this mode)
Button/switch count
4. Whenever target buttons or target switches are operated, the but-
ton/switch count is decreased.
Target buttons (17 types):
[
i
OUTPUT STEREO/L/R], [LIGHT], [VOL +], [VOL
−
], [T-
MARK], [
x
STOP], [
X
REC PAUSE], [
z
REC], [C1], [C2],
[•BACK/ HOME], [OPTION], [
v
DPC], [ A-B
V
], [
.
],
[
>
], [
N
]
Target switches (14 types):
[POWER] (“ON” direction), [HOLD] (“ON” direction), [MIC
ATT] (“20” direction), [MIC/LINE INPUT LEVEL] ((MIC/
LINE input type selection) “MIC” direction/“LINE” direction),
[XLR/TRS INPUT LEVEL] ((XLR/TRS input type selection
L side) “MIC” direction/“LINE” direction), [XLR/TRS IN-
PUT LEVEL] ((XLR/TRS input type selection R side) “MIC”
direction/“LINE” direction), [+48V] ((L side) “ON” direction),
[+48V] ((R side) “ON” direction), [INPUT] (“MIC/LINE”
direction/“XLR/TRS” direction), built-in microphones position
(both L/R microphones are tilted inward)
5. After all buttons and switches are decided, return to test mode
menu screen.
Note:
If the releasing this mode on the way, return to the test mode menu
screen by removing the batteries, inserting them again and turning the
power on.
Even if you removed the batteries, test mode is not released.
SYS SET
2019/03/08 01:38:10 (GMT+09:00)