Sony PCM-D10 Скачать руководство пользователя страница 45

Страница: 45 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-25. XLR ASSY

four screws

(Z1.7

4.5)

,QVWDOODWLRQGLUHFWLRQRIWKHIOH[LEOHIODWFDEOH3

XLR board
(CN003)

[blue]

[white]

SW board
(CN703)

flexible flat cable

(18P)

(CN003)

terminal
side

Remove the XLR block in

the direction of the arrow.

Draw the flexible flat cable (18P)

out of the connector (CN703).

XLR block

front side

top side

bottom side

XLR assy

(See

Note)

Turn
around.

spacer

(XLR

front)

spacer

(XLR

front)

spacer

(XLR

rear)

spacer

(XLR

rear)

3DVWLQJSRVLWLRQRIWKHVSDFHU;/5

guide line

spacer (XLR front)

spacer (XLR rear)

spacer (XLR front)

spacer (XLR rear)

–

%RWWRPYLHZ

–

guide line

Note:

When the XLR assy is replaced, make sure to refer to “XLR/TRS JACK CHECKING METHOD”

on page 15, and check the XLR/TRS jack.

Insert straight into
the interior.

Insert at a slant.

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

Insert only part way.

+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH

  Insert the flexible flat cable straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

Insert straight into
the interior.

flexible flat
cable

connector

flexible flat
cable

connector

Insert only part way.

spacer (XLR front)

spacer (XLR rear)

2.15 mm

6.0 mm

1.65 mm

7.5 mm

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 45 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: