Sony PCM-D10 Скачать руководство пользователя страница 29

Страница: 29 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-7. CABINET (REAR) ASSY

0000000

0123456

groove

top side

bottom side

claw

two foots

(See Fig. C)

Open the lid (battery).

knob (BATT)

serial number label

(See

Note)

cabinet (rear) assy

(See

Note)

3DVWLQJSRVLWLRQRIWKHVHULDOQXPEHUODEHO

serial number label

guide line

Affixed at a slant.

Not affixed within the affixing
border for serial number label.

Press the claw in the direction

of the arrow to remove it from

the

groove.

Note:

When the cabinet (rear) assy is replaced, make sure to peel off the serial number label

from the old cabinet (rear) assy and affix it to the new one.

foot mounting
hole

+RZWRLQVWDOOWKHIRRW

)LJ&!

When installing the foot, align the rib
of foot and groove of foot mounting
hole.

groove

rib

foot

Press.

rib

foot

Press.

groove

foot mounting hole
(See Fig. C)

affixing border for
serial number label

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 29 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: