Sony PCM-D10 Скачать руководство пользователя страница 3

PCM-D10

3

Sony CONFIDENTIAL

For Authorized Servicer

Input/output

t

XLR/TRS jack(s)

MIC (MIC ATT: 0) 

Input impedance: 32 kΩ (phantom power: OFF) 
Rated input level: -48 dBu 
Minimum input level: -58 dBu 

LINE 

Input impedance: 12 kΩ 
Rated input level: +6 dBu 
Minimum input level: -3 dBu 
Maximum input level: +12 dBu

t

Headphone jack (stereo mini-jack) 
Rated output level: 400 mV 
Maximum output level: 35 mW + 35 mW or above (load impedance: 16 Ω) 
Recommended load impedance: 16 Ω to 32 Ω

t

LINE OUT jack (stereo mini-jack) 
Output impedance: 220 Ω 
Rated output level: +4 dBV 
Recommended load impedance: 22 kΩ

t

USB port (USB Type-C port) Hi-speed USB compatible

t

Card slot: SD card slot

Playback speed control 
(DPC)

t

1.00 times - 0.25 times: 
FLAC files with the sampling frequency at 88.2 kHz or above

t

2.00 times - 0.25 times: 
LPCM files with the sampling frequency at 88.2 kHz or above, FLAC files 
with the sampling frequency below 88.2 kHz

t

3.00 times - 0.25 times: other than the above

Speaker maximum power 
output

200 mW

Power requirements

Four LR6 (size AA) alkaline batteries (supplied): 6 V DC
Four nickel metal hydride rechargeable batteries NH-AA (not supplied):  
4.8 V DC

Ambient conditions

Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Operating humidity: 25 % - 75 %
Storage temperature: -10 °C - +45 °C (14 °F - 113 °F)
Storage humidity: 25 % - 75 %

Dimensions (not including 
projecting parts and 
controls)

Approx. 80.2 mm x 197.6 mm x 37.4 mm (3.16 in x 7.78 in x 1.48 in)
(Width/Height/Depth)

Mass

Approx. 480 g (16.94 oz) (including batteries)

Supplied accessories

USB Type-C™ cable (USB-A to USB-C) (1)
Carrying pouch (1)
Wind screen (1)
Sony LR6 (size AA) alkaline batteries (4)
Operating Instructions
SOUND FORGE Audio Studio 12 Installation Guide (1)

*

1

A small amount of the built-in memory is used for file management and therefore not available for user storage.

*

2

Applies when the built-in memory is formatted by the linear PCM recorder.

*

3

Not all encoders are supported.

*

4

Playback of the MP3 files recorded by the linear PCM recorder is also supported.

*

5

WMA Ver.9 is compatible, however, MBR (Multi Bit Rate), Lossless, Professional, and Voice are not supported.

*

6

Copyright-protected files are not available for playback.

*

7

Applies to the following recording modes: 
– LPCM 192 kHz 24 bit 
– LPCM 176.4 kHz 24 bit 
– LPCM 96 kHz 24 bit 
– LPCM 88.2 kHz 24 bit 
– LPCM 48 kHz 24 bit 
– LPCM 44.1 kHz 24 bit

*

8

Applies to the following recording modes: 
– LPCM 192 kHz 24 bit 
– LPCM 176.4 kHz 24 bit 
– LPCM 96 kHz 16/24 bit 
– LPCM 88.2 kHz 16/24 bit 
– LPCM 48 kHz 16/24 bit 
– LPCM 44.1 kHz 16/24 bit

*

9

Varies depending on the communication conditions.

*

10

A Bluetooth profile is a specification that standardizes features of individual characteristics of the Bluetooth 
device.

*

11

Audio compression conversion method

Design and specifications are subject to change without notice.

Maximum recordable time*

The total maximum recordable time of all the folders is as follows.

REC Mode

Built-in memory

LPCM 192kHz/24bit (STEREO)

LPCM 176.4kHz/24bit (STEREO)

LPCM 96kHz/24bit (STEREO)

LPCM 96kHz/16bit (STEREO)

LPCM 88.2kHz/24bit (STEREO)

LPCM 88.2kHz/16bit (STEREO)

LPCM 48kHz/24bit (STEREO)

LPCM 48kHz/16bit (STEREO)

LPCM 44.1kHz/24bit (STEREO)

LPCM 44.1kHz/16bit (STEREO)

3 hours 15 minutes

3 hours 35 minutes

6 hours 35 minutes

9 hours 55 minutes

7 hours 10 minutes

10 hours 45 minutes

13 hours 15 minutes

19 hours 50 minutes

14 hours 25 minutes

21 hours 35 minutes

MP3 320 kbps (STEREO)

95 hours 25 minutes

MP3 128 kbps (STEREO)

238 hours

REC Mode

Memory card

16 GB

32GB

64GB

128 GB

256GB

LPCM 192kHz/24bit 
(STEREO)

LPCM 176.4kHz/24bit 
(STEREO)

LPCM 96kHz/24bit 
(STEREO)

LPCM 96kHz/16bit 
(STEREO)

LPCM 88.2kHz/24bit 
(STEREO)

LPCM 88.2kHz/16bit 
(STEREO)

LPCM 48kHz/24bit 
(STEREO)

LPCM 48kHz/16bit 
(STEREO)

3 hours
40 minutes

4 hours

7 hours
25 minutes

11 hours
10 minutes

8 hours
5 minutes

12 hours
10 minutes

14 hours
50 minutes

22 hours
20 minutes

5 minutes

7 hours
25 minutes

8 hours

14hours
50 minutes

22 hours
20 minutes

16 hours
10 minutes

24 hours
20 minutes

29 hours
45 minutes

44 hours
40 minutes

10 minutes

14 hours
50 minutes

16 hours

29 hours
45 minutes

44 hours
40 minutes

32 hours
25 minutes

48 hours
40 minutes

59 hours
35 minutes

89 hours
25 minutes

25 minutes

29 hours
45 minutes

32 hours

59 hours
35 minutes

89 hours
25 minutes

64 hours
55 minutes

97 hours
20 minutes

119 hours

178 hours

55 minutes

59 hours
35 minutes

64 hours

119 hours

178 hours

129 hours

194 hours

238 hours

357 hours

REC Mode

Memory card

16 GB

32 GB

64GB

128GB

256 GB

LPCM 44.1kHz/24bit 
(STEREO)

LPCM 44.1kHz/16bit 
(STEREO)

MP3 320 kbps  
(STEREO)

MP3 128 kbps  
(STEREO)

16 hours
10 minutes

24 hours
20 minutes

107 hours

268 hours

32 hours
25 minutes

48 hours
40 minutes

214 hours

536 hours

64 hours
55 minutes

97 hours
20 minutes

429 hours

1,073 hours

124 hours

194 hours

858 hours

2,147 hours

259 hours

389 hours

1,717 hours

4,294 hours

* The maximum recordable time in this topic is provided for your reference only, and may differ depending on the 

card specifications.

Maximum recordable time per file*

1

 *

2

The maximum recordable times provided here are all approximate.

REC Mode

Built-in memory

LPCM 192kHz/24bit (STEREO)

LPCM 96kHz/24bit (STEREO)

LPCM 44.1kHz/16bit (STEREO)

1 hour

2 hours

6 hours 45 minutes

MP3 320 kbps (STEREO)

7 hours 25 minutes

MP3 128 kbps (STEREO)

18 hours 30 minutes

*

The maximum recordable time in this topic is provided for your reference only.

*

If the file size reaches the maximum limit (4 GB for an LPCM file, and 1 GB for an MP3 file) during recording, the 
file will be divided.

The maximum playback time of a music file/number of files *

Bit rate

Playback time

Number of files

128 kbps

238 hours

3,570 files

256 kbps

119 hours

1,785 files

* In the case where MP3 files of 4 minutes each are transferred to the linear PCM recorder.

Battery life

When using alkaline batteries (Continuous using of Sony alkaline battery LR6(SG)) *

The battery’s life spans provided here are all approximate.

REC Mode

Recording

Recording 

(Phantom power for 

XLR microphone: ON)

Playback 

built-in 

through 

speakers

Playback 

with 

headphones

Recording 

with REC 

Remote

Playback 

via the 

Bluetooth 

connection

while 
monitoring

not while 
monitoring

while 
monitoring

not while 
monitoring

LPCM  
192kHz/24bit 
(STEREO)

LPCM  
96kHz/24bit 
(STEREO)

LPCM  
48kHz/24bit 
(STEREO)

LPCM  
44.1kHz/16bit 
(STEREO)

MP3 320kbps 

26 hours

28 hours

30 hours

30 hours

30 hours

32 hours

36 hours

44 hours

44 hours

44 hours

6 hours

6 hours

6 hours

6 hours

6 hours

6 hours

6 hours

6 hours

6 hours

6 hours

38 hours

52 hours

60 hours

62hours

64 hours

40 hours

54 hours

62 hours

70 hours

74 hours

22 hours

24 hours

26 hours

26 hours

26 hours

40 hours

48 hours

54 hours

56 hours

60 hours

(STEREO)

* Measured values acquired under our measurement conditions. The battery life may shorten depending on how 

you operate the linear PCM recorder.

System requirements

When you use the linear PCM recorder connected to a computer or as a USB mass storage device, 
your computer must meet the operating system requirements and port environment described 
below.
To use your computer with the SOUND FORGE Audio Studio 12 software, refer to “SOUND FORGE 
Audio Studio 12 Installation Guide” (supplied separately).

Operating systems

t

Windows 10/Windows 8.1/Windows 7 (Service Pack 1 or higher)

t

macOS (v10.10 - v10.14)

Note

t

One of the above operating systems should be by default pre-installed. Any operating system other than those 
indicated above, upgraded operating systems or multi-boot environment are not supported.

t

For the latest version information and compatibility with your operating system, please access the customer 
support home page (page 85) for the linear PCM recorder.

Hardware environment

t

Port: USB port

t

Disc drive: To create a music CD, you need a CD-R/RW drive.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Отзывы: