Sony PCM-D10 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 68

Sony PCM-D10 Скачать руководство пользователя страница 42

PCM-D10

42

Sony CONFIDENTIAL

For Authorized Servicer

2-22. MAIN BOARD BLOCK

rear side

top side

bottom side

4

screw

(Z1.7

u

4.5)

4

screw

(Z1.7

u

4.5)

4

screw

(Z1.7

u

4.5)

5

ML plate (PWB)

5

ML plate (PWB)

hole

7

MAIN board block

Note:

When installing the MAIN board

block, align the two holes and two

battery

terminals.

hole

3

Remove the solder of the

two battery terminals.

battery terminal M
(BATT)

2

flexible flat cable (14P)

(CN341)

1

flexible flat cable (6P)

(CN342)

terminal
side

terminal
side

Insert straight into
the interior.

OK

Insert at a slant.

Insert at a slant.

NG

NG

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

flexible flat
cable

connector

connector

colored line

flexible flat
cable

connector

Insert only part way.

How to install the flexible flat cable

  Insert the flexible flat cable straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

6

Insert straight into
the interior.

OK

NG

flexible flat
cable

connector

NG

flexible flat
cable

connector

Insert only part way.

battery terminal P
(BATT)

chassis (rear) block

– Chassis (rear) block rear view –

battery
terminal L
(BATT P-M)

battery
terminal L
(BATT P-M)

battery
terminal R
(BATT P-M)

battery
terminal P
(BATT)

battery
terminal M
(BATT)

top side

Note about installing the chassis (rear) block

Before installing the chassis (rear) block to the MAIN board
block, check that all of the battery terminals on the battery
installation side of the chassis (rear) block have not fallen out
or are not missing.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

«
...
40
41
42
43
44
...
»

Содержание PCM-D10





































































Отзывы:

Нет отзывов