Sony PCM-D10 Скачать руководство пользователя страница 32

Страница: 32 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-10. MIC_JACK BOARD

front side

top side

bottom side

terminal
side

rib

hole

Insert straight into the interior.

Insert at a slant.

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

Insert only part way.

How to install the flexible flat cable

  Insert the flexible flat cable straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

chassis (jack)

Note

When installing the chassis (jack),

align the two ribs and two holes.

Remove two solder of the MIC

SW board (L) wire. [blue/gray]

Remove two solder of the MIC

SW board (R) wire. [brown/gray]

Remove two solder

of the MIC (R) wire.

[red/gold]

Remove two solder

of the MIC (L) wire.

[red/gold]

screw

(Z1.7

4.5)

flexible flat cable

(12P)

(CN955)

screw (M1.4)

(L = 2.5 mm)

Remove the MIC_JACK board

in the direction of the arrow.

Lift up the MIC_JACK

board in the direction

of the arrow.

MIC_JACK board

hole

boss

hole

jack

MIC_JACK board

Note

When installing the MIC_JACK

board, align the jack and hole.

top side

MIC_JACK board

0,&ZLUHVHWWLQJ

MIC (R)
wire [red]

MIC (R)
wire [gold]

MIC SW board
(R) wire [gray]

MIC SW board
(R) wire [brown]

MIC (L)
wire [red]

MIC (L)
wire [gold]

MIC SW board
(L) wire [gray]

MIC SW board
(L) wire [blue]

Press the MIC wire into the slit
of MIC_JACK board.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 32 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: