Sony PCM-D10 Скачать руководство пользователя страница 43

Страница: 43 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-23. MAIN BOARD

flexible flat cable (10P)

(CN651)

flexible flat cable (12P)

(CN401)

terminal side

Remove four solders of

the flat cable HP (4P).

Remove four solders of

the flat cable HP (4P).

insulating sheet PWB

insulating
sheet PWB

insulating

sheet

PWB

MAIN board

(See Note 1)

• Flat cable HP (4P) setting

MAIN board

[red]
[blue]

flat cable HP (4P)

[red]

[blue]

< Fig. F >

• Installation direction of the flexible flat cable (12P)

MAIN
board

[blue]

[white]

MIC_JACK
board

Note 1:

When the MAIN board is replaced, make sure to refer to

the following pages and perform each procedure.

DESTINATION SETTING METHOD (page 8)

BLUETOOTH CONNECTION CHECKING METHOD (page 10)

XLR/TRS JACK CHECKING METHOD (page 15)

LINE OUT JACK CHECKING METHOD (page 19)

• Pasting position of the insulating sheet PWB

flat cable HP (4P)

(See Fig. F)

Note

When the MAIN board is replaced,

the flat cable HP (4P) is included

with the MAIN board.

flat cable HP (4P)

(See Fig. F)

Note

When the MAIN board is replaced,

the flat cable HP (4P) is included

with the MAIN board.

Insert at a slant.

flexible flat
cable

connector

• How to install the flexible flat cable

  Insert the flexible flat cable straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

Insert straight into
the interior.

flexible flat
cable

connector

flexible flat
cable

connector

Insert only part way.

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 43 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: