Sony PCM-D10 Скачать руководство пользователя страница 39

Страница: 39 / 68

PCM-D10

Sony CONFIDENTIAL

For Authorized Servicer

2-17. SW_L BOARD

Insert straight into the interior.

Insert at a slant.

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

colored line

flexible flat
cable

connector

Insert only part way.

How to install the flexible flat cable

  Insert the flexible flat cable straight into the interior.
  There is a possibility that using this unit without the
  connector correctly installed will damage it.

four screws

(Z1.7

4.5)

flexible flat cable

(14P)

(CN851)

terminal
side

front side

top side

bottom side

Remove the SW_L board block

in the direction of the arrow.

SW_L board

Note

When installing the SW_L board,

align the two bosses and two holes.

hole

boss

Note 1:

If the SW_L board was replaced, make sure to refer to “BLUETOOTH CONNECTION

CHECKING METHOD” on page 10 and check the Bluetooth connection.

2-18. CHASSIS (MAIN)

Turn over.

rear side

top side

bottom side

top side

guide line

3DVWLQJSRVLWLRQRIWKHDGKHVLYHVKHHW(/

adhesive sheet (EL)

three screws

(Z1.7

4.5)

main plate (PWB)

screw

(Z1.7

4.5)

adhesive sheet (EL)

six screws

(Z1.7

4.5)

chassis (main) block

cushion (SP)

chassis (main)

bottom side

top side

SYS SET

2019/03/08 01:38:10 (GMT+09:00)

Содержание PCM-D10





































































Результаты поиска

Содержание PCM-D10

Отзывы:

Sony PCM-D10, Руководство по обслуживанию, Страница: 39 / 68

Результаты поиска

Содержание PCM-D10

Отзывы: