SII IP-6900 Скачать руководство пользователя

Страница: 253 / 266

6-4

When an Error Message Appears

If the ERROR lamp lights, check the message to be displayed on
the LCD.
There are four types of error messages.

- Service call errors:

Operator unrecoverable errors, such as H/W, S/W failure.
Contact our service center.

- Communication errors:

Communication protocol errors.
Take appropriate action according to the error code or
message.

- Operator call errors:

The operator can correct these errors.
Take appropriate action according to the message.

The error messages are as follows. Take appropriate action
according to the error message.

If a communication error or a data error occurs, the ERROR

lamp does not light. An error message appears on the LCD
and disappears when the next operation is performed.

Service Call Errors

If any of the following service call error messages appears, turn
the power switch OFF and then ON again. This may release

the error condition.

nnnn: Error code

Description

: An unrecoverable error has occurred in the engine section.

(This error message appears when an error is detected
during self-diagnosis after the power is turned ON.)

Measure

: Contact your dealer or our service center (the error code on

the LCD is needed) .

HINT

INITIALIZING

E E n n n n

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды