SII IP-6900 Скачать руководство пользователя

Страница: 53 / 266

2-9

Section 2 Basic Operations

Turning the Power ON/OFF

NOTE

- Turn the printer OFF while “PRINT READY” is displayed on

the LCD panel except in an emergency.

Do not turn the printer OFF while “INITIALIZING” or

“CLEANING” is displayed on the LCD panel to avoid dripping

of the ink and damage of the head. Saved parameters may

be lost.

- If the fan does not run or the operation panel lamp does not

light when the AC1 switch and power ON/OFF switch on the
operational panel are turned ON, the power supply may be
faulty.

- If an error is detected during the self-diagnostic test at power

ON, an error message appears on the LCD. See Section 5,
Troubleshooting, and take appropriate action.

HINT

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды