SII IP-6900 Скачать руководство пользователя

Страница: 260 / 266

6-11

Section 6 T

roubleshooting

(Others)

Description

: The rear cover is opened.

Measure

: Take appropriate action according to the message.

Description

: The head temperature is out of the operating temperature

range.

Measure

: Stay within the operating temperature range. Leave the

printer idle for a while until the head temperature falls
within the range.

Description

: The ambient temperature is not within the operating

temperature range for the printer.

Measure

: Stay within the operating temperature range (15

C to

C).

Description

: It is about time to change the cap pump.

Measure

: Please contact our service center to have the cap pump

changed.

Description

: It is about time to change the ink supply pump.

Measure

: Please contact our service center to have the ink supply

pump changed.

CLOSE REAR COVER

HEAD TEMP. ERROR

WAIT A MOMENT

ENV. TEMP. ERROR

CHANGE CONDITION

TIME TO CHANGE

CAP PUMP

TIME TO CHANGE

XX PUMP

When an Error Message Appears

XX: Ink color

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды