manualshive.com logo in svg

SII IP-6900, Руководство пользователя


Поделиться
Скачать
background image

2-41

Section 2  Basic Operations

Replacing Ink Cartridges

This section describes how to replace an ink cartridge.
Ink cartridges should be installed in the following four cases:

- If ink has run out
- If an ink cartridge is not installed
- If a 4-color ink cartridge is to be replaced
- If a 6-color ink cartridge is to be replaced

The ink cartridge replacement procedure in each case is explained
below.

Ink Cartridge Replacement Procedure

1

Open the ink cover.

Ink cartridge

NOTES

Ink cover

Push here to open the ink cover.

-

Do not remove the ink cartridge in the following cases:

•

No power is supplied to the printer due to a power failure

or breaker action.

•

An error other than ink end has occurred.

-

Depending on the printer status, the ink in the ink box may

spill, causing malfunction.

-

Select the offline state if the ink cartridge in which the ink

remains is replaced. (

⇒

 See Section 3, Ink Menu (5))

For ink replacement during printing, see "Replacing the

cartridge during printing".

-

Make sure the ink cartridge is right side up before installing.

Содержание IP-6900











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP-6900

Canon UFR II User Manual preview
UFR II
Бренд: Canon Страницы: 149
Canon G650 Getting Started preview
G650
Бренд: Canon Страницы: 60
Lanier LD116 Quick Manual preview
LD116
Бренд: Lanier Страницы: 4
Samsung CLP 510N - Color Laser Printer Manual Del Usuario preview
CLP 510N - Color Laser Printer
Бренд: Samsung Страницы: 270
Samsung Bixolon SRP-270 Integrator'S Manual preview
Bixolon SRP-270
Бренд: Samsung Страницы: 13
Oki C9850hdn Safety Manual preview
C9850hdn
Бренд: Oki Страницы: 48
Oki C3520 Network Manual preview
C3520
Бренд: Oki Страницы: 34
Oki C3200n Reference preview
C3200n
Бренд: Oki Страницы: 65
Oki C6100dn Safety Information Manual preview
C6100dn
Бренд: Oki Страницы: 44
Oki C6100dn Setup Manual preview
C6100dn
Бренд: Oki Страницы: 36
OHAUS SF40A User Manual preview
SF40A
Бренд: OHAUS Страницы: 28
Oce cm2520 User Manual preview
cm2520
Бренд: Oce Страницы: 396
Oce cm2510 Safety Manual preview
cm2510
Бренд: Oce Страницы: 28
Oki CX 1145 MFP Safety & Warranty Manual preview
CX 1145 MFP
Бренд: Oki Страницы: 64
Datamax MP-Compact4 Programmer'S Reference Manual preview
MP-Compact4
Бренд: Datamax Страницы: 95
Datamax Mark II E-4205e Operator'S Manual preview
Mark II E-4205e
Бренд: Datamax Страницы: 72
Samsung SCX 4500W - Personal Wireless Laser Multi-Function... User Manual preview
SCX 4500W - Personal Wireless Laser Multi-Function...
Бренд: Samsung Страницы: 113
Canon imageRUNNER ADVANCE 8105 Specification preview
imageRUNNER ADVANCE 8105
Бренд: Canon Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды