SII IP-6900 Скачать руководство пользователя

Страница: 161 / 266

3-33

Section 3 Operation Panel Menu Operations

(14) Color stripe setting (COLOR STRIPE)

Sets color stripe print ON/OFF.

<Parameter (Enter a choice)>
- ON: Prints the color stripe print on the origin side.
- OFF: Does not print the color stripe on the origin side.

(15) Head action mode setting

Selects a head action mode.

<Parameter (Enter a choice)>
- NORMAL:

Use this usually.

- HIGHLIGHT:

Use this for print gradation data.

#COLOR STRIPE

>01 : ON

- If the color stripe is not set, dot-off in printing may occur.

It is recommended to set the color stripe for printing, if

practicable.

- The color stripe is printed on the test print regardless of

this setting.

NOTES

If a pattern having very low printing rate in even one color is

printed continuously at high temperature, gaps in printing may

occur at a low printing rate color. In this case, set the head

mode to HILIGHT PRIORITY.

NOTE

#HEAD MOTION

>01 : NORMAL

Menu Operations

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды