SII IP-6900 Скачать руководство пользователя

Страница: 30 / 266

1-8

Ink Cartridge

Ink types

Use our recommended ink cartridges listed below.

[6-color ink cartridge] 1 cartridge/box

NOTES

- Failure to use the recommended ink cartridge may lead to

deterioration of print quality or printer malfunction.

- The ink lifetime is 12 months after the manufacture date.

- Do not shake ink cartridges before use.

- All six color cartridges must be installed.

If any of the cartridges is removed, install a new one.

Item No.

Ink color

Ink capacity

IP6-101 Y (Yellow)

1000 ml

IP6-102 M (Magenta)

1000 ml

IP6-103 C (Cyan)

1000 ml

IP6-104 Bk (Black)

1000 ml

IP6-105 Lc (Light Cyan)

1000 ml

IP6-106 Lm (Light Magenta)

1000 ml

Item No.

Ink color

Ink capacity

IP6-141 Y (Yellow)

1000 ml

IP6-142 M (Magenta)

1000 ml

IP6-143 C (Cyan)

1000 ml

IP6-144 Bk (Black)

1000 ml

[4-color ink cartridge] 3 cartridge/box

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды