SII IP-6900 Скачать руководство пользователя

Страница: 145 / 266

3-17

Section 3 Operation Panel Menu Operations

Basic Operations and Keys

(1) To enable menu operations:

- Enter the offline mode.
- When the printer enters the offline mode, a menu group screen is

displayed.

(2) Menu group selection:

- Select a menu group directly with the

and

keys.

- Switch between menu group screens with the

key.

(3) Menu selection:

keys

: Change between menus at the same level.

key

: Return to menu group selection.

key

: Select a menu so that parameters can be

changed.

(4) Parameter setting or change:

keys

: Switch between parameters.

Increment or decrement a value when it is
entered.

keys : Shift digit when entering a value.

(5) Parameter setting or canceling:

key

: Set a parameter.

key

: Cancel an input parameter value and return to

the menu selection.

(6) Save:

- The changes in the Setup menu, System menu, and Mechanical

Adj. menu are automatically saved as parameters.

(7) End of setting:

- When the

key is pressed, the printer goes back to the

online mode.

Basic Menu Operation in Offline State

Содержание IP-6900











































































































































































































































































Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды

SII IP-6900, Руководство пользователя

Результаты поиска

Содержание IP-6900

Отзывы:

Похожие инструкции для IP-6900

Бренды по названию

Популярные бренды