Siemens SIWAREX WP251 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 220

Siemens SIWAREX WP251 Скачать руководство пользователя страница 75

Scale parameters and functions

8.3 DR 3 Calibration parameters

SIWAREX WP251
Manual, 12/2015, A5E37203357A

75

8.3.31

Weighing operating mode

The parameter defines the operating mode of the scale.
The following operating modes are available:
0: Non-automatic weighing instrument (NAWI) – Filling

1: Non-automatic weighing instrument (NAWI) – Removal

10: Automatic

gravimetric instrument – Filling

20: Automatic catchweighing instrument - Filling

21: Automatic catchweighing instrument - Removal

8.3.32

SecureDisplay including weighing range data

In legal trade operation, the software version of the HMI device must be recorded so that it

can be checked by an official verification officer.

8.3.33

SecureDisplay interface

For applications requiring official calibration, the "SecureDisplay" software is used to display

the calibratable weight value. The parameter defines whether "SecureDisplay"

communicates directly via the Ethernet port of the WP251 or via the Ethernet port of the

SIMATIC S7-1200 CPU.

8.3.34

SecureDisplay version

For applications requiring official calibration, the "SecureDisplay" software is used to display

the calibratable weight value. The parameter defines the version of the "SecureDisplay"

software that is running in the HMI device. If the version is not entered correctly, a weight

value will not be output in "SecureDisplay", and the display stays in the "Start Up" step.

8.3.35

Smallest zoom factor of SecureDisplay

The minimum display size defines the smallest zoom factor for the "SecureDisplay"

calibratable display. If the parameter does not match the smallest zoom factor in the .xml file

in the HMI device, "SecureDisplay" remains in the "StartUp "step and no weight value is

output.

8.3.36

Grid frequency

The parameter defines the line frequency of the power supply grid. A selection between 50

Hz and 60 Hz can be made. By making the correct setting, interferences caused by the

power supply grid can be better suppressed.

«
...
73
74
75
76
77
...
»

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды