Siemens SIWAREX WP251 Скачать руководство пользователя страница 103

Страница: 103 / 220

Scale parameters and functions

8.14 DR 14 Selection process value 1, 2

SIWAREX WP251
Manual, 12/2015, A5E37203357A

103

8.13.6

RS485 number of stop bits

This parameter defines the number of stop bits for the RS485 interface.

Value

Stop bits

0 (default) 1
1

8.13.7

RS485 Modbus address

This parameter defines the Modbus address (1 to 255) for communication via the RS485

interface with the Modbus protocol.

8.13.8

Decimal place for Siebert indicator

A fixed decimal place must be specified if a Siebert indicator is used. The following values

are permitted: 0 ... 4

8.14

DR 14 Selection process value 1, 2

The weighing module can communicate with an S7-1200 CPU in two ways: Via the I/O only

or by reading/writing complete data records. The I/O is faster in this case and exhibits a

higher performance because the data is made available to the S7-1200 or SIWAREX

automatically in each PLC cycle. Using two user-definable channels in the S7-I/O (process

value 1 and process value 2), the user can decide which scale values (see table) are to be

made available cyclically to the PLC in these two parameters.

Table 8- 13 Selection table for process value 1,2

Process value

Function code

From DR

Format

No value selected

Gross weight

FLOAT

Gross/net weight (default)

FLOAT

Tare weight

FLOAT

Gross process weight

FLOAT

Gross/net process weight

FLOAT

Tare process weight

FLOAT

Net weight x10

FLOAT

Status of analog output, digital out-

puts and inputs (see table)

LONG

NAWI Status bits (default)

USHORT

Refresh counter

UINT

Содержание SIWAREX WP251





























































































































































































































Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX WP251, Руководство пользователя

Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды