manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 46

Commissioning 

 

7.4 Quick calibration with calibration weights and SIWATOOL 

 

SIWAREX WP251 

46

 

Manual, 12/2015, A5E37203357A 

7.4

 

Quick calibration with calibration weights and SIWATOOL 

7.4.1

 

Introduction 

In order to perform the quick calibration with calibration weights, the parameters marked in 

bold font in data records DR 3 and DR 10 must first be defined. The procedure is described 

below. 

7.4.2

 

Activate service mode 

Service mode must be activated in order to change the calibration parameters. You can find 

the command in the "Service Commands" group (spanner icon). 

7.4.3

 

Load standard parameters 

The quick setup is based on the standard settings of the weighing module. Therefore, the 

standard parameter settings must be reset prior to the quick setup. Firstly, service mode is 

activated; the standard parameters are subsequently loaded using the "Load standard 

parameters (12)" command. 
The parameters must then be read from the SIWAREX in SIWATOOL using "Communication 

→ Receive all data".

 

7.4.4

 

Input of required parameters 

For commissioning, you must enter the following parameters in data record DR 3 and send 

these to the module: 

●

 

Unit of weight 

●

 

Required maximum weighing range of the scale 

●

 

Scale interval 

●

 

Calibration weight 0, 1 and optionally 2 

The description of the parameters can be obtained from the description of data record DR 3. 
Sending/receiving a data record is always carried out by right-clicking on the data record 

name in the "Value" column in the tree structure.  
For example, if data record 3 is to be sent, right-click on "Calibration parameter (DR3)". A 

submenu is then opened with the option for sending the respective data record to the 

weighing module or for reading it from the module. All data records can only be sent as 

complete packets to the SIWAREX or read from it. It is not possible to read or write individual 

parameters within a data record. Therefore the complete data record must initially be 

received for every change to parameters within it. The desired parameter can then be edited, 

and the data record returned. If the data record is not received, the danger exists that 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды