Siemens SIWAREX WP251 Скачать руководство пользователя страница 199

Страница: 199 / 220

Operation requiring official calibration

12.2 Verification

SIWAREX WP251
Manual, 12/2015, A5E37203357A

199

In turn, the "Calibration check" submenu branches into three submenus with the contents as

shown in the following table.

"Version and variables check" submenu
Switch over the representation of the SecureDisplay

Display or hide the SecureDisplay using command buttons
Switch over between 5 possible displays of variables using

buttons 1 to 5
Show smallest possible display using command button.
In the area of the calibration data (display "Advanced scale

parameters 4 of 4), the smallest zoom factor is applied

which still results in a readily readable display size. Follow-

ing the verification, users can only select larger windows for

the calibration display.

Switch over contents of the SecureDisplay, the display

switches back automatically to the weight display

Display SecureDisplay version
Display calibration regulation
Display scale data
Display SIWAREX serial number
Display SIWAREX firmware release

"Scale check" submenu
Switch over contents of the SecureDisplay

x 10 increased resolution (5 s)
Display current tare (5 s)

Scale commands

Set to zero
Tare setting (current weight or default values)
Delete tare
Logging

Tare specification

Using the tare specification button you can access the form

for entering various specific tare values

"Logbook check" submenu
Display logbook entries

Only the software downloads for the legal trade display

SecureDisplay are retained in the logbook. It is not possible

to download the firmware following verification of the scale

with the jumper for write protection inserted.

Display first logbook entry
Display last logbook entry
Display previous logbook entry
Display next logbook entry

Содержание SIWAREX WP251





























































































































































































































Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX WP251, Руководство пользователя

Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды