manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 123

 

Scale parameters and functions 

 

8.23 DR 24 Controller and filter parameters 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

123

 

8.23.2

 

Parameter relation 

This parameter defines the unit in which the "Maximum corrective action" and "Controller 

deadband - upper/lower limit" parameters (DR 24) must be interpreted. The following options 

are available: 

 

Function 

code 

Meaning 

0 (default) 

"Maximum corrective action" and "Controller deadband - upper/lower limit" are inter-

preted as a percentage of the set point (DS 20). 

1 

"Maximum corrective action" and "Controller deadband - upper/lower limit" are inter-

preted in the weight unit. 

8.23.3

 

Type of controller 

A proportional controller is available for optimization of the shut-off points. 

 

Function 

code 

Meaning 

0  

No controller 

1 (default) 

Proportional controller is activated 

 
 

 

Note 
Stop weighing cycle 
If a weighing cycle has been stopped by a Stop command in the meantime, there is no 

corrective action by the controller for this dosing! The controller becomes active only for 

completed and checked cycles. 

 

8.23.4

 

Control factor of proportional controller 

When proportional controller is activated, its control factor can be defined. The parameter is 

specified as a percent. 

8.23.5

 

Maximum corrective action 

When proportional controller is activated, the maximum possible correction of the shut-off 

points by the controller can be defined. Depending on the "Parameter relation" setting (DR 

24), the value must be specified and interpreted as a percentage of the set point (DR 20) or 

as an absolute weight value. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды