manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 117

 

Scale parameters and functions 

 

8.22 DR 23 Material parameters 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

117

 

8.21.10

 

Number of not controlled weighings 

This parameter defines how many cycles will not be checked for tolerance during continuous 

operation in AWI mode. The first dosing cycle of the continuous operation is always checked 

for tolerance, however. The discontinuation of the check(s) starts only after a dosing with 

"Good" tolerance has been determined. Dosings that are not checked for tolerance are 

classified as "GOOD" in the statistics (DR 39). 

 

 

Note 
Dosing cycles that cannot be checked 
In unchecked cycles, there is no adjustment of the shut-off points by the proportional 

controller. 
Every dosing that is not checked is classified as "Good" in the statistics and the specified set 

point (DS 20) is used in calculating the statistics. 

 

8.21.11

 

Capture of weighings into statistics 

This parameter defines, based on the tolerance evaluation, which dosing results are to be 

included in the statistics calculation and which are not. The following options are available for 

selection: 

 

Function code  Meaning 
0 (default) 

All dosings (with tolerance check) are included following "Dosing completed" in the 

calculated statistics. 

1 

Dosings (with tolerance check) of "GOOD" class are included following "Dosing 

completed" in the calculated statistics. 

2 

Dosings (with tolerance check) of "BAD" class are not included following "Dosing 

completed" in the calculated statistics. 

 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды